Complete Repeater/Amplifier System

Works with all 1900 Mhz. PCS service providers including Sprint, T-Mobile, AT&T, Cingular or Verizon and with all generations of protocol CDMA, GSM, TDMA,and 3G.

Not sure if 1900 Mhz. is what you need? Then go to this website www.wirelessadvisor.com and enter your zip code to See If Your Provider Is Using The 1900 Mhz. PCS Band In Your Area. If your provider is listed as using just a 1900 Mhz. (1.9 Ghz.) network for your area then this is the system you want. If however your provider lists both the 1900 Mhz. & the 800 Mhz. bands then it will take a bit more digging to find out which is going to be right. What it means when your provider lists both bands, is that their network has some cells that operate at 800 Mhz. and some that are operating at 1900 Mhz.. Phone, PDA, etc., don't give any indication what frequency they are operating at. However they all have the ability to switch from one band to the next just as seamlessly as they pass your signal off from one cell to the next when your moving. If your provider lists both frequencies then the only way to be sure what frequency the cell that is closest to the location where you want to set the Repeater/Amplifier up at is to contact the provider and ask. By giving your provider the location were you want to install this system they can determine which cell in their network is closest and what frequency it is operating at. If it's 800 Mhz. then you will need to have a 800 Mhz. system.

Offer Includes: Wilson Electronic's latest technology, the 1900 Mhz. 60 dB Smart Tech Repeater/Amplifier Part # 801306 with AC power supply

Offer Includes: Wilson Electronic's High Gain 13 dB Yagi Antenna (Part # 301124).

Offer Includes: Wilson Electronic's ceiling mounted Dome Antenna (Part # 301121).

Offer Includes: 2(Two) separate lengths of Ultra low loss feedline with the necessary Male N connectors installed. 1(One) 50' (Part # 951106) to run from the outside mounted Yagi antenna to the Repeater/Amplifier, and 1(One) 30' (Part # 951105) to run from the Repeater/Amplifier to the Inside mounted Dome antenna.

There is nothing else you should need to buy but possibly a mast and grounding hardware for the outside antenna.

Advanced Electronics Receive & Transmit Better Than Your Cellphone, PDA or Air Card modem*

Wireless Operation - No Physical Connection to Cellphone

Allows Multiple Phones and PCS devices to be Used Simultaneously

Significantly Increases Your PCS Device's Range on Send & Receive

Safer than using your PCS device without an amplifier**

Extends the Life of Your PCS device's Battery**

This offer is for a complete turn key Wilson Electronics 60 dB* 1900 Mhz. PCS in building Smart Tech Wireless Repeater/Amplifier System. We have put this package together with providing the best possible performance as our goal. Only the best, proven highest performance components are included with this package. Don't confuse one of these systems with the "made in china" desktop units your seeing pop up on ebay these days. Those devices operate under FCC Part 15 rules. This means their output cannot surpass 500 milliwatts. This output level can't come close to covering the same area that the up to 3 watts output* that these systems have do. With our package you will get the latest technology Wilson Electronics has to offer, the 60 dB* Smart Tech Wireless Repeater/Amplifier with a plug in AC power supply. You also will get the 9 element Wilson Electronics 13 dB gain Yagi Antenna for outside, and the ceiling mounted Wilson Electronics dual polarized "Dome" antenna for inside. To hook it all up with you will get Two lengths, One 50, and One 30 foot (total of 80 ') of ultra low loss 9913/LMR-400 equivalent feedline with all necessary connectors pre-installed. You will need nothing else to install your own Wireless 1900 Mhz. PCS Repeater/Amplifier System but possibly a mast and grounding equipment for the outside antenna.

* The Wilson Wireless Repeater/Amplifier has the ability to amplify the signal it receives by as much as 60 dB, up to a total output power of 3 watts! It's micro-processor based controls continuously monitor the signal quality turning the power up as needed to maintain a clear static free connection with the cell.. If the full 3 watts is not needed for a crystal clear signal, then the micro-processor throttles back the output power reducing component heating/wear and tear.

* *The Wilson Cellular Repeater/Amplifier has a better receiver than what's in your cellphone. Its advanced electronics are very sensitive and able to receive minute signals which would go undetected by most cellphones. It also has a better transmitter with several, several times the power output of your cellphone.

*** A cellphone using our Repeater/Amplifier is safer and will use less battery power because the phone thinks it's much closer to a cell site than it actually is. Phones vary their power output based on their proximity to cell sites. Therefore, your phone transmits less power - resulting in safer use from a lower power level being radiated next to your head and longer battery life.